Used Profurl Jib Furler / Roller Furling / Reefing System (Lot#1891)

Description

Lot # 1891
Used Profurl Jib Furler / Roller Furling / Reefing System
Model: Cruiser
Boat Length Range: 30'-34'
Total Roller Furler System Length: 40'8" (you can buy additional foils to increase length)
Headstay Max Diameter: 1/4"
BASE UNIT:
Base Unit To Deck Fitting: SS Chain Plates
Base Unit To Deck Fitting Fastener: Bolt
Forestay Adjustment: None Provided, see mfg. specs
Forestay Wire to Adjustment: None Provided, see mfg. specs
Drum Condition: Very Good
Drum Overall Diameter: 7"
Drum Height (from bottom fastener center to top of drum): 1'7"
Jib Tack (forward bottom jib attachment fixture): None Provided, see mfg. specs
Jib Tack Height (from bottom fastener center to jib forward foot attachment point): 1'9""
Total Base Unit Length (from bottom fastener center and drum and jib tack ((jib sail forward lower attachment point)) and top of feeder foil ((bottom foil is special and often different lengths)): 8'2"
FOILS:
Foil Condition: Very Good
Foil Design: Single Groove, Round
Foil Total Length:32'6"
Each Factory Foil 6'6" x Number Factory Foil (5)=Total Factory Foil Lengths 32'6"
Total Base Unit Length: 8'2"
Plus Total Foils Length 32'6"=Total Roller Furler System Length 40'8"
Foil Connectors: 5 needed included
Foil Insert Type: Split
Foil Connector Fasteners: 28 needed, 8 included, 12 (not included)
Head Swivel Condition: Very Good
Head Swivel Sail Attachment: None
Head Swivel Halyard Attachment: None
Anti-Halyard Snag Device: No
WHAT YOU NEED TO INSTALL THIS ROLLER FURLER SYSTEM:
Foil Fasteners: 12 needed (allen)
Head Swivel Jib Head Attachment, example:
shackle
Forestay: Anti-wrap Fitting, Turnbuckle needed
Upper Clevis Pin needed
Loctite Thread Lock, Super Lube Grease, Line Jib Halyard, Drum Line, Drum Fairlead Pulley, Stanchion Fairlead, Drum Line Cleat needed
HOW TO SIZE YOUR BOAT FOR A ROLLER FURLER SYSTEM
1. Jib Height:  Decide what height off deck you wish the jib tack (lower forward attachment point).  Will the sail clear the bow pulpit? Can you see under the jib easily?
2. Drum Height:   What height do you want the drum? you can add toggles or most companies offer short and tall lower attachment chainplates.  We will specify the drum height off deck we are selling.
3. Roller Furler System Length:  Tie a long line securly onto the jib halyard, raise it up to the desired height (usually 12" below top, (see sailboat mfg. recommendation jib length and furler mfg. recommendation for upper halyard to mast pulley angle), and mark at lower pin attachment point, (take this opportunity to inspect jib halyard) lower line and measure = total roller furler system length.
4. Base Unit: We sell the base unit includes the Lower Attachment + Drum + Tack (jib sail forward lower attachment point) +  Feeder Foil (bottom foil is special).  See listing for base unit height.
5. Foil Total Length Needed:  Roller Furler System Length - Base Unit Height = Total Foil Length needed
6. Number of Foils Needed:  Total Foil Length Needed divided by Length per Foil (see listing) = Number of Foils Needed
7. Note: we sell different foil lengths (see listing), sometimes there are bonus short foils.
8. See What You Need to Install section, buy roller furler, read on line mfg. installation instructions.
9. Size Jib:  while assembled roller furler system is on ground, install desired sail attachment shackles or snap shackles, now make a accurate measure of jib luff , consult SailMaker for advice on luff dimension.